ZSSKC 131 025-9+026-7

yuz6099 hat eine neue Datei hinzugefügt:

Datei

ZSSKC 131 025-9+026-7

Slovak electric loco produced by Skoda Plzen.

yuz6099

11. Februar 2020

Zitat

First beta version of locomotive Skoda 58E (ZSSKC class 131). This version includes custom script for loco and interior. Interior is in beta state (not all the features i've planned are implemented yet). But already there's a launch sequence that has to be completed.

In cab mode:

0. Select first unit
1. press Shift+Space to turn on battery

2. Set swtich (2) to state P.K., wait until sound stops
3. Set switch (3) to state Z, wait 4 seconds
4. Press button (4)
5. Rotate switches (5) and (6)
6. Set switches (7, 8 ) to state A
7. Set brake lever (9) to state O
8. Wait until compressors shut down, set brake lever to state J
9. Set reverse (11)
10. Optionally turn of headlight (12) and front/back ditchlights (13,14,15,16)
11. You are ready to drive, Use throttle controller (18) to adjust the throttle. (be careful with "+" and "-" modes)
12. Set throttle controller to state "+1" and relese it. Then set the controller to "+1" again, you will hear the sound of ventilators and loco will start moving.
13. Continue increasing throttle positions, but remember that motor current displayed at ammeter (19) should be under 350 A for optimal loco performance.
14. Use loco brake (17) if needed.

Note: there are 42 throttle positions. At position 37 ventilators turn off and you have to be very careful with next throttle position as they seriously increase motor current.

Note 2: it is better not to use "S" button for throttle reset. Use controller (18). Also, try to keep 2 second delay after you switched from 1 to second position.

Note 3: Train brake lever notches:
S - fast increasing of the pressure in brake cylinders
P - slow increasing of the pressure in brake cylinders
Z - lap
O - release
J - initial
B - service braking
R - emergency

Note 4: most of the buttons work, but you have to manually set it to 0 position after you pressed it. Basically, don't release the mouse after you pressed the button, drag the button back to initial state with mouse.

Note 5: Electrodynamic brake isn't implemented yet.

Thanks for everyone who's been helping me those 3 years. Special thanks for Mika, Slovak_Eagle, @cj187 and wearsprada.

List of DLS kuids:

<kuid2:404575:1870201004:11> |CJ| Corona - Dimmed Headlight (Warm White)

<kuid2:30671:925059004:2> Engine sand

<kuid2:517519:100836:2> Skoda horn #1

<kuid2:404575:1870104017:10> |CJ| Coupler-Library (Red)

<kuid2:404575:1870103001:15> |CJ| German train script library

<kuid2:404575:1870104018:10> |CJ| Coupler-Library (Yellow)

<kuid2:506034:100026:1> dummy Engine Sound

<kuid:388413:372005> NBSdeps invisible pant

<kuid2:388413:439002:1> NBS+ MathPlus Library V2 (its now a static class!)

<kuid2:151055:60033:2> Russian Diesel Locomotive Keyboard

<kuid2:404575:1870103001:15> |CJ| German train script library

List of non-DLS kuids (should be on the DLS in several days):

<kuid2:517519:133:1> Skoda 3/25 LSP panto (yellow weathered)

<kuid2:517519:1141:1> Hum bogey sound

<kuid2:517519:13166:1> Skoda 58E cab TRS19 beta

<kuid2:517519:1134:1> Skoda Sound Library #1

<kuid2:517519:134:1> Skoda 3/25 LSP panto inv (yellow weathered)

<kuid2:506034:456862:1> Red Corona bufer

<kuid2:517519:1135:1> Skoda 58E script library

<kuid2:517519:13151:1> Skoda 58E bogey

<kuid2:517519:13152:1> Skoda 58E enginespec

<kuid2:506034:456877:1> White Corona bright

<kuid2:506034:456860:1> White Corona bufer

Alles anzeigen

yuz6099 hat eine neue Version hinzugefügt:

Datei

ZSSKC 131 025-9+026-7

Slovak electric loco produced by Skoda Plzen.

yuz6099

11. Februar 2020

Zitat

First beta version of locomotive Skoda 58E (ZSSKC class 131). This version includes custom script for loco and interior. Interior is in beta state (not all the features i've planned are implemented yet). But already there's a launch sequence that has to be completed.

version 1.0.1 - script hotfix

In cab mode:

0. Select first unit

1. press Shift+Space to turn on battery skip this

2. Set swtich (2) to state P.K., wait until sound stops

3. Set switch (3) to state Z, wait 4 seconds

4. Press button (4)

5. Rotate switches (5) and (6)

6. Set switches (7, 8 ) to state A

7. Set brake lever (9) to state O

8. Wait until compressors shut down, set brake lever to state J

9. Set reverse (11)

10. Optionally turn of headlight (12) and front/back ditchlights (13,14,15,16)

11. You are ready to drive, Use throttle controller (18) to adjust the throttle. (be careful with "+" and "-" modes)

12. Set throttle controller to state "+1" and relese it. Then set the controller to "+1" again, you will hear the sound of ventilators and loco will start moving.

13. Continue increasing throttle positions, but remember that motor current displayed at ammeter (19) should be under 350 A for optimal loco performance.

14. Use loco brake (17) if needed.

Note: there are 42 throttle positions. At position 37 ventilators turn off and you have to be very careful with next throttle position as they seriously increase motor current.

Note 2: it is better not to use "S" button for throttle reset. Use controller (18). Also, try to keep 2 second delay after you switched from 1 to second position.

Note 3: Train brake lever notches:

S - fast increasing of the pressure in brake cylinders

P - slow increasing of the pressure in brake cylinders

Z - lap

O - release

J - initial

B - service braking

R - emergency

Note 4: most of the buttons work, but you have to manually set it to 0 position after you pressed it. Basically, don't release the mouse after you pressed the button, drag the button back to initial state with mouse.

Note 5: Electrodynamic brake isn't implemented yet.

Thanks for everyone who's been helping me those 3 years. Special thanks for Mika, Slovak_Eagle, @cj187 and wearsprada.

List of DLS kuids:

<kuid2:404575:1870201004:11> |CJ| Corona - Dimmed Headlight (Warm White)

<kuid2:30671:925059004:2> Engine sand

<kuid2:517519:100836:2> Skoda horn #1

<kuid2:404575:1870104017:10> |CJ| Coupler-Library (Red)

<kuid2:404575:1870103001:15> |CJ| German train script library

<kuid2:404575:1870104018:10> |CJ| Coupler-Library (Yellow)

<kuid2:506034:100026:1> dummy Engine Sound

<kuid:388413:372005> NBSdeps invisible pant

<kuid2:388413:439002:1> NBS+ MathPlus Library V2 (its now a static class!)

<kuid2:151055:60033:2> Russian Diesel Locomotive Keyboard

<kuid2:404575:1870103001:15> |CJ| German train script library

List of non-DLS kuids (should be on the DLS in several days):

<kuid2:517519:133:1> Skoda 3/25 LSP panto (yellow weathered)

<kuid2:517519:1141:1> Hum bogey sound

<kuid2:517519:13166:1> Skoda 58E cab TRS19 beta

<kuid2:517519:1134:1> Skoda Sound Library #1

<kuid2:517519:134:1> Skoda 3/25 LSP panto inv (yellow weathered)

<kuid2:506034:456862:1> Red Corona bufer

<kuid2:517519:1135:1> Skoda 58E script library

<kuid2:517519:13151:1> Skoda 58E bogey

<kuid2:517519:13152:1> Skoda 58E enginespec

<kuid2:506034:456877:1> White Corona bright

<kuid2:506034:456860:1> White Corona bufer

Alles anzeigen

yuz6099 hat eine neue Version hinzugefügt:

Datei

ZSSKC 131 025-9+026-7

Slovak electric loco produced by Skoda Plzen.

yuz6099

11. Februar 2020

Zitat

First beta version of locomotive Skoda 58E (ZSSKC class 131). This version includes custom script for loco and interior. Interior is in beta state (not all the features i've planned are implemented yet). But already there's a launch sequence that has to be completed.

version 1.0.1 - script hotfix

In cab mode:

0. Select first unit

1. press Shift+Space to turn on battery skip this

2. Set swtich (2) to state P.K., wait until sound stops

3. Set switch (3) to state Z, wait 4 seconds

4. Press button (4)

5. Rotate switches (5) and (6)

6. Set switches (7, 8 ) to state A

7. Set brake lever (9) to state O

8. Wait until compressors shut down, set brake lever to state J

9. Set reverse (11)

10. Optionally turn of headlight (12) and front/back ditchlights (13,14,15,16)

11. You are ready to drive, Use throttle controller (18) to adjust the throttle. (be careful with "+" and "-" modes)

12. Set throttle controller to state "+1" and relese it. Then set the controller to "+1" again, you will hear the sound of ventilators and loco will start moving.

13. Continue increasing throttle positions, but remember that motor current displayed at ammeter (19) should be under 350 A for optimal loco performance.

14. Use loco brake (17) if needed.

Note: there are 42 throttle positions. At position 37 ventilators turn off and you have to be very careful with next throttle position as they seriously increase motor current.

Note 2: it is better not to use "S" button for throttle reset. Use controller (18). Also, try to keep 2 second delay after you switched from 1 to second position.

Note 3: Train brake lever notches:

S - fast increasing of the pressure in brake cylinders

P - slow increasing of the pressure in brake cylinders

Z - lap

O - release

J - initial

B - service braking

R - emergency

Note 4: most of the buttons work, but you have to manually set it to 0 position after you pressed it. Basically, don't release the mouse after you pressed the button, drag the button back to initial state with mouse.

Note 5: Electrodynamic brake isn't implemented yet.

Thanks for everyone who's been helping me those 3 years. Special thanks for Mika, Slovak_Eagle, @cj187 and wearsprada.

List of DLS kuids:

<kuid2:404575:1870201004:11> |CJ| Corona - Dimmed Headlight (Warm White)

<kuid2:30671:925059004:2> Engine sand

<kuid2:517519:100836:2> Skoda horn #1

<kuid2:404575:1870104017:10> |CJ| Coupler-Library (Red)

<kuid2:404575:1870103001:15> |CJ| German train script library

<kuid2:404575:1870104018:10> |CJ| Coupler-Library (Yellow)

<kuid2:506034:100026:1> dummy Engine Sound

<kuid:388413:372005> NBSdeps invisible pant

<kuid2:388413:439002:1> NBS+ MathPlus Library V2 (its now a static class!)

<kuid2:151055:60033:2> Russian Diesel Locomotive Keyboard

<kuid2:404575:1870103001:15> |CJ| German train script library

List of non-DLS kuids (should be on the DLS in several days):

<kuid2:517519:133:1> Skoda 3/25 LSP panto (yellow weathered)

<kuid2:517519:1141:1> Hum bogey sound

<kuid2:517519:13166:1> Skoda 58E cab TRS19 beta

<kuid2:517519:1134:1> Skoda Sound Library #1

<kuid2:517519:134:1> Skoda 3/25 LSP panto inv (yellow weathered)

<kuid2:506034:456862:1> Red Corona bufer

<kuid2:517519:1135:1> Skoda 58E script library

<kuid2:517519:13151:1> Skoda 58E bogey

<kuid2:517519:13152:1> Skoda 58E enginespec

<kuid2:506034:456877:1> White Corona bright

<kuid2:506034:456860:1> White Corona bufer

Alles anzeigen

To everyone who has downloaded old version: please, re-download, i've fixed battery switch.

no, TRS19 only