Die aktuelle Version lässt sich sowieso nicht mehr in PTP2 verwenden. Ich benutze eine etwas ältere. Also wäre das, was ich da habe final für PTP2.
-
-
@Sebastian Eben. Die "Finale" Version des Talent wäre ja so inkompatibel wie nur irgend möglich. Klar, ist der dann auf T:ANE total realistisch, aber das ist dann ein ganzer Befehlshaufen, denn man dann entfernen muss. Dass sich bei einem Cab besser eins von BSI verwenden lässt, unterstütze ich aber auch, denn man möchte eher nicht auf die EbuLas verzichten (und keine neuen schreiben).
Es gibt hier im Forum durchaus eine kleine PTP2 Gemeinde, die T:ANE auch nicht besitzt. Die tauchen nur nicht bei jedem Talent 2 Thread auf, um ihren Senf dazuzugeben und nach dem Zug zu betteln.Ich wollte ja auch nur fragen, ob es möglich wär, den TS12 Zug nocheinmal hochzuladen. Kompatibel mit PTP2 kann ich mir den schon selber machen. Außerdem kommen jetzt vielleicht auch noch TS12 Nutzer in dieses Forum, und haben dann mit dem TANE-Zug ähnliche Probleme.
-
Die ältere Version ist nach wie vor dort verfügbar, wo es sie vorher auch schon gab, ich habe ihn dort nicht gelöscht.
-
@ProjektTramburg Stimmt, ich glaube ich werde mir dann einfach das RE160-Cab so modifizieren, dass es wie das Talent 2-Cab aussieht.
Die sehen sich ja sehr ähnlich.Gruss
simufanSo gibt ein Problem:
Nur das "daycab.im" wird durch die Angabe 'position' erhöht, die Schalter nicht und alles andere nicht.
Ich wollte alles im Führerstand um einen Meter erhöhen, weil ich unterhalb der Bahnsteigkante saß.
Hier ist ein Ausschnitt aus der config.txt:Code: config.txt
Alles anzeigentag { mesh "daycab/re160-day.im" att-parent "default" att "a.basis" auto-create 1 position 0,0,1 } nacht { mesh "nightcab/re160_night.im" att-parent "default" att "a.basis" auto-create 0 position 0,0,1 } wiper { mesh "wiper/wiper.im" att "a.wiper" att-parent "default" auto-create 1 anim "wiper/wiper.kin" animation-loop-speed 0 position 0,0,1 } rollor { kind "lever" auto-create 1 mesh "daycab/sitz.im" att "a.sitz" limits 0,1 angles 0,-3 radius 0.5 mousespeed 1 att-parent "default" position 0,0,1 } rollor_night { kind "lever" auto-create 1 mesh "nightcab/sitz.im" att "a.sitz" limits 0,1 angles 0,-3 radius 0.5 mousespeed 1 att-parent "default" position 0,0,1 } rollo { kind "lever" auto-create 1 mesh "daycab/rollo.im" att "a.rollo" limits 0,1 angles 0.017,0.0109 radius 0.1 mousespeed -2 att-parent "default" position 0,0,1 } rollo_night { kind "lever" auto-create 0 mesh "nightcab/rollo.im" att "a.rollo" limits 0,1 angles 0.017,0.0109 radius 0.1 mousespeed -2 att-parent "default" position 0,0,1 } schifere { kind "lever" mesh "daycab/fensterr.im" att "a.fensterr" limits 0,1 angles 0.0084,-0.006 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } schifeli { kind "lever" mesh "daycab/fensterl.im" att "a.fensterl" limits 0,1 angles -0.0084,0.006 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } schifere_night { kind "lever" mesh "nightcab/fensterr.im" att "a.fensterr" limits 0,1 angles 0.0084,-0.006 mousespeed 1 att-parent "default" auto-create 0 position 0,0,1 } schifeli_night { kind "lever" mesh "nightcab/fensterl.im" att "a.fensterl" limits 0,1 angles -0.0084,0.006 mousespeed 1 att-parent "default" auto-create 0 position 0,0,1 } accelerator2 { kind "needle" mesh "dial/nadel.im" att "a.ri01" limits -20,20 angles -2.4,2.4 att-parent "default" auto-create 1 position 0,0,1 } tacho { kind "needle" mesh "dial/nadel_2.im" att "a.ri02" limits 0,50 angles -2.495,2.51 att-parent "default" auto-create 1 position 0,0,1 } accelerator { kind "needle" mesh "dial/david.im" att "a.ri03" limits 0,20 angles -0.07,0.4 att-parent "default" auto-create 1 position 0,0,1 } brakepipe2 { kind "needle" mesh "dial/david_2.im" att "a.ri05" limits 0,1000 angles -0.07,0.4 att-parent "default" auto-create 1 position 0,0,1 } brakecyl2 { kind "needle" mesh "dial/david_2.im" att "a.ri04" limits 0,1000 angles -0.07,0.4 att-parent "default" auto-create 1 position 0,0,1 } v_soll_needle { kind "needle" mesh "dial/v_soll.im" att "a.ri02" limits 0,50 angles -2.495,2.51 att-parent "default" auto-create 1 position 0,0,1 } afb_vsoll_needle { kind "needle" mesh "dial/afb_soll.im" att "a.ri09" limits 0,50 angles -2.35,2.26 att-parent "default" auto-create 0 position 0,0,1 } bptrainbrakepipe_needle { kind "needle" mesh "dial/brems_k.im" att "a.ri10" limits 0,1000 angles 2.4,-2.4 att-parent "default" auto-create 1 position 0,0,1 } bptrainbrakecylinder_needle { kind "needle" mesh "dial/brems.im" att "a.ri08" limits 0,1000 angles 2.4,-2.4 att-parent "default" auto-create 1 position 0,0,1 } bplocomain_needle { kind "needle" mesh "dial/brems_k2.im" att "a.ri11" limits 0,1000 angles 2.4,-2.4 att-parent "default" auto-create 1 position 0,0,1 } throttle_lever { kind "lever" mesh "lever/f_hebel.im" att "a.sth1" limits 0,8 angles -0.6,0.5 notches 0,0.125,0.25,0.375,0.5,0.625,0.75,0.875,1 notchheight 1,2,2,2,2,2,2,2,1 radius 0.15 mousespeed 2 att-parent "default" auto-create 1 position 0,0,1 } reverser_lever { kind "lever" mesh "lever/rev.im" att "a.sth2" limits 0,2 angles 0.5,-0.5 notches 0,0.5,1 notchheight 1,1,1 radius 0.001 att-parent "default" auto-create 1 position 0,0,1 } trainbrake_lever { kind "lever" mesh "lever/f_hebel_2.im" att "a.sth4" limits 0,4 angles 0.5,-0.6 notches 0,0.25,0.27,0.29,0.31,0.33,0.35,0.37,0.39,0.41,0.43,0.45,0.47,0.49,0.5,0.75,1 notchheight 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1 mousespeed -2 radius 0.15 att-parent "default" auto-create 1 position 0,0,1 } independantbrake_lever { kind "lever" mesh "lever/f_hebel.im" att "a.sth5" limits 0,32 angles 0.5,-0.6 notches 0,0.1,0.2,0.3,0.4,0.5,0.6,0.7,0.8,0.9,1 notchheight 1,2,2,2,2,2,2,2,2,2,1 mousespeed -1 radius 0.15 att-parent "default" auto-create 1 position 0,0,1 } sifa { kind "lever" mesh "lever/hebel.im" att "a.hs01" limits 0,1 angles -0.1,0.6 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } luefter { kind "lever" mesh "lever/hebel.im" att "a.hs09" limits 0,1 angles -0.1,0.6 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } stromabnehmer2 { kind "lever" mesh "lever/hebel.im" att "a.hs10" limits 0,1 angles -0.1,0.6 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } streckenmonitor { kind "lever" mesh "lever/hebel_k.im" att "a.hs11" limits 0,1 angles 0.5,-0.5 notches 0,1 notchheight 0.1,0.1 radius 0.01 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } stromabnehmer { kind "lever" mesh "lever/hebel.im" att "a.hs12" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } hauptschalter { kind "lever" mesh "lever/hebel_cy.im" att "a.hs13" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } instrumentenbeleuchtung { kind "lever" mesh "lever/hebel.im" att "a.hs15" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } sifa_ein_aus { kind "lever" mesh "lever/hebel_k.im" att "a.hs20" limits 0,1 angles 0.5,-0.5 notches 0,1 notchheight 0.1,0.1 radius 0.01 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } pzb_ein_aus { kind "lever" mesh "lever/hebel_k.im" att "a.hs21" limits 0,1 angles 0.5,-0.5 notches 0,1 notchheight 0.1,0.1 radius 0.01 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } pzb_befehl { kind "lever" mesh "lever/befehl.im" att "a.hs22" limits 0,1 angles 0,-0.02 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } pzb_frei { kind "lever" mesh "lever/hebel.im" att "a.hs23" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } pzb_wachsam { kind "lever" mesh "lever/hebel_rd.im" att "a.hs24" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } beleuchtung_fuehrerraum { kind "lever" mesh "lever/hebel.im" att "a.hs26" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } light_switch { kind "lever" mesh "lever/hebel.im" att "a.hs27" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } horn { kind "lever" mesh "lever/hebel.im" att "a.hs30" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } sanden { kind "lever" mesh "lever/hebel_rd.im" att "a.hs32" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } pzb_wachsam_r { kind "lever" mesh "lever/hebel_rd.im" att "a.hs33" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } pzb_wachsam_l { kind "lever" mesh "lever/hebel_rd.im" att "a.hs34" limits 0,1 angles -0.1,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } pzb_befehl_r { kind "lever" mesh "lever/befehl.im" att "a.hs35" limits 0,1 angles 0,-0.02 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } pzb_befehl_l { kind "lever" mesh "lever/befehl.im" att "a.hs36" limits 0,1 angles 0,-0.02 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } pzb_frei_r { kind "lever" mesh "lever/befehl.im" att "a.hs37" limits 0,1 angles 0,-0.02 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } pzb_frei_l { kind "lever" mesh "lever/befehl.im" att "a.hs38" limits 0,1 angles 0,-0.02 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed -1 att-parent "default" auto-create 1 position 0,0,1 } tuer_zu_rechts { kind "lever" mesh "lever/hebel_w.im" att "a.hs41" limits 0,1 angles -0.5,0.5 notches 0,1 notchheight 0.1,0.1 radius 0.01 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } luftpresser { kind "lever" mesh "lever/hebel.im" att "a.hs45" limits 0,1 angles -0.1,0.6 notches 0,1 notchheight 0.1,0.1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } notaus { kind "lever" mesh "lever/not.im" att "a.dk01" limits 0,1 angles 0,-0.1 notches 0,1 notchheight 0.1,0.1 radius 0.3 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } tuersteuerung { kind "lever" mesh "lever/dreh.im" att "a.dr06" limits 0,1 angles -3,3 notches 0,0.25,0.5,0.75,1 notchheight 1,2,2,2,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } wischer { kind "lever" mesh "lever/stell.im" att "a.sth08" limits 0,1 angles 0.8,-0.8 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } fussbodenheizung { kind "lever" mesh "lever/dreh.im" att "a.dr14" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } betriebsart { kind "lever" mesh "lever/dreh.im" att "a.dr199" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } notbremsventil { kind "lever" mesh "lever/notbremsventil.im" att "a.sth7" limits 0,1 angles -1.57,0 notches 0,1 notchheight 1,1 mousespeed 2 radius 0.15 att-parent "default" auto-create 1 position 0,0,1 } stirnfensterheizung { kind "lever" mesh "lever/dreh.im" att "a.dr30" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } nischenheizung { kind "lever" mesh "lever/dreh.im" att "a.dr22" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } luefter2 { kind "lever" mesh "lever/dreh.im" att "a.dr16" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } temperatur { kind "lever" mesh "lever/dreh.im" att "a.dr17" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } klima { kind "lever" mesh "lever/dreh.im" att "a.dr18" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } abfahrschalter_rechts { kind "lever" mesh "lever/dreh_w.im" att "a.dr19" limits 0,4 angles 0.4,-2 notches 0,0.25,0.5,0.75,1 notchheight 1,2,2,2,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } abfahrschalter_links { kind "lever" mesh "lever/dreh_w.im" att "a.dr20" limits 0,4 angles -0.4,2 notches 0,0.25,0.5,0.75,1 notchheight 1,2,2,2,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } druckschutz { kind "lever" mesh "lever/dreh.im" att "a.dr21" limits 0,1 angles -1,1 notches 0,1 notchheight 1,1 radius 0.1 mousespeed 1 att-parent "default" auto-create 1 position 0,0,1 } leuchtmelder2 { kind "light" mesh "light/lm02.im" att "a.lm02" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder3 { kind "light" mesh "light/lm03.im" att "a.lm03" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder5 { kind "light" mesh "light/lm05.im" att "a.lm05" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder6 { kind "light" mesh "light/lm06.im" att "a.lm06" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder7 { kind "light" mesh "light/lm07.im" att "a.lm07" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder8 { kind "light" mesh "light/lm08.im" att "a.lm08" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder9 { kind "light" mesh "light/lm09.im" att "a.lm09" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder10 { kind "light" mesh "light/lm10.im" att "a.lm10" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder11 { kind "light" mesh "light/lm11.im" att "a.lm11" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder12 { kind "light" mesh "light/lm12.im" att "a.lm12" auto-create 0 att-parent "default" position 0,0,1 } leuchtmelder13 { kind "light" mesh "light/lm13.im" att "a.lm13" auto-create 0 att-parent "default" position 0,0,1 } mmi_startup_screen { kind "light" mesh "display2/david_grund.im" att "a.david" auto-create 1 att-parent "default" position 0,0,1 } main_off { kind "light" mesh "display/main-off.im" att "a.disp_vorn" auto-create 1 att-parent "default" position 0,0,1 } david_off { kind "light" mesh "display/david-off.im" att "a.david" auto-create 1 att-parent "default" position 0,0,1 } ebula_startup_screen { kind "light" mesh "display/ebula00.im" att "a.ebula" auto-create 0 att-parent "default" position 0,0,1 } ebula_leer_screen { kind "light" mesh "display/ebula02.im" att "a.ebula" auto-create 1 att-parent "default" position 0,0,1 effects { ebula_fahrplan { kind "texture-replacement" texture "display/ebula01.texture" } } } ebula_diag_screen { kind "light" mesh "display/ebula01.im" att "a.ebula" auto-create 0 att-parent "default" position 0,0,1 } ebula_ausschalten_info { kind "light" mesh "display/button13.im" att "a.ebula08" auto-create 0 att-parent "default" position 0,0,1 } ebula_diagnose_info { kind "light" mesh "display/button01.im" att "a.ebula10" auto-create 0 att-parent "default" position 0,0,1 } ebula_home_info { kind "light" mesh "display/button02.im" att "a.ebula09" auto-create 0 att-parent "default" position 0,0,1 } zeile1 { kind "light" mesh "display/text00.im" att "a.ebula00" auto-create 0 att-parent "default" position 0,0,1 } zeile2 { kind "light" mesh "display/text01.im" att "a.ebula01" auto-create 0 att-parent "default" position 0,0,1 } zeile3 { kind "light" mesh "display/text02.im" att "a.ebula02" auto-create 0 att-parent "default" position 0,0,1 } zeile4 { kind "light" mesh "display/text04.im" att "a.ebula03" auto-create 0 att-parent "default" position 0,0,1 } zeile5 { kind "light" mesh "display/text05.im" att "a.ebula04" auto-create 0 att-parent "default" position 0,0,1 } zeile6 { kind "light" mesh "display/text06.im" att "a.ebula05" auto-create 0 att-parent "default" position 0,0,1 } zeile7 { kind "light" mesh "display/text07.im" att "a.ebula06" auto-create 0 att-parent "default" position 0,0,1 } ebula_ein_aus { kind "lever" mesh "display/transknopf.im" att "a.ebula14" limits 0,1 angles 0,0.02 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } home { kind "lever" mesh "display/transknopf.im" att "a.ebula15" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } diagnose { kind "lever" mesh "display/transknopf.im" att "a.ebula16" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } vorheriger_fahrplan { kind "lever" mesh "display/transknopf.im" att "a.ebula25" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } naechster_fahrplan { kind "lever" mesh "display/transknopf.im" att "a.ebula26" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } vorherige_seite { kind "lever" mesh "display/transknopf.im" att "a.ebula28" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } naechste_seite { kind "lever" mesh "display/transknopf.im" att "a.ebula27" limits 0,1 angles 0,0.17 notches 0,1 notchheight 0,0 radius 0.02 mousespeed 15 auto-create 1 att-parent "default" position 0,0,1 } }
Gruß
simufan -
So, ist zwar nicht perfekt, dafür 100% PTP2-kompatibel.
Ist bald fertig, darf ihn leider nicht teilen
Der hat doch keine LZB, oder?
Wo auf dem Monitor blinkt in der Realität das SIFA-Licht auf?Gruß
simufan -
Ich würde mal sagen, im MFD
-
Ja, das ist mir klar, aber an welcher Stelle im MFD?
Über das DB-Logo kommt doch auch noch was (also da wo es weiss ist). Konnte das auf einigen echten Fotos sehen.Gruß
simufan -
Ein Tag Dauerarbeit und es ist fertig. Ich musste nochmal Attachmentpoints anpassen und Hebel "umherschubsen" und Skripte umgehen, aber nun ist der Führerstand fertig
Thema ist hiermit erledigt.
Gruß
simufan -
100%? Also PZB funktioniert auch einwandfrei?
Übrigens gibt´s meines Wissens nach nen RE160 Cab ohne LZB.
-
@ProjektTramburg ist egal, die LZB habe ich in dem Cab schon "ermordet"